264 research outputs found
Integrated gas turbine engine-nacelle
A nacelle for use with a gas turbine engine is provided with an integral webbed structure resembling a spoked wheel for rigidly interconnecting the nacelle and engine. The nacelle is entirely supported in its spacial relationship with the engine by means of the webbed structure. The inner surface of the nacelle defines the outer limits of the engine motive fluid flow annulus, while the outer surface of the nacelle defines a streamlined envelope for the engine
Integrated gas turbine engine-nacelle
A nacelle for use with a gas turbine engine is presented. An integral webbed structure resembling a spoked wheel for rigidly interconnecting the nacelle and engine, provides lightweight support. The inner surface of the nacelle defines the outer limits of the engine motive fluid flow annulus while the outer surface of the nacelle defines a streamlined envelope for the engine
Quiet Clean Short-haul Experimental Engine (QCSEE) Under-The-Wing (UTW) composite nacelle subsystem test report
The element and subcomponent testing conducted to verify the under the wing composite nacelle design is reported. This composite nacelle consists of an inlet, outer cowl doors, inner cowl doors, and a variable fan nozzle. The element tests provided the mechanical properties used in the nacelle design. The subcomponent tests verified that the critical panel and joint areas of the nacelle had adequate structural integrity
Recommended from our members
DEGAS 2 neutral transport modeling of high density, low temperature plasmas
Neutral transport in the high density, low temperature plasma regime is examined using the DEGAS 2 Monte Carlo neutral transport code. DEGAS 2 is shown to agree with an analytic fluid neutral model valid in this regime as long as the grid cell spacing is less than twice the neutral mean-free path. Using new atomic physics data provided by the collisional radiative code CRAMD, DEGAS 2 is applied to a detached Alcator C-Mod discharge. A model plasma with electron temperature {approximately}1 eV along detached flux tubes, between the target and the ionization front, is used to demonstrate that recombination is essential to matching the experimental data. With the CRAMD data, {approximately}20% of the total recombination is due to molecular activated recombination
Recommended from our members
Spectroscopic diagnostics of tritium recycling in TFTR
The authors present the first spectroscopic measurements of tritium Balmer-alpha (T{sub {alpha}}) emission from a fusion plasma. A Fabry-Perot interferometer is used to measure the H{sub {alpha}}, D{sub {alpha}}, T{sub {alpha}} spectrum in the current D-T a experimental campaign on TFTR and the contributions of H, D and T are separated by spectral analysis. The T{sub {alpha}} line was measurable at concentrations T{sub {alpha}}/(H{sub {alpha}} + D{sub {alpha}} + T{sub {alpha}}) down to 2%
Validation in Fusion Research: Towards Guidelines and Best Practices
Because experiment/model comparisons in magnetic confinement fusion have not
yet satisfied the requirements for validation as understood broadly, a set of
approaches to validating mathematical models and numerical algorithms are
recommended as good practices. Previously identified procedures, such as
verification, qualification, and analysis of error and uncertainty, remain
important. However, particular challenges intrinsic to fusion plasmas and
physical measurement therein lead to identification of new or less familiar
concepts that are also critical in validation. These include the primacy
hierarchy, which tracks the integration of measurable quantities, and
sensitivity analysis, which assesses how model output is apportioned to
different sources of variation. The use of validation metrics for individual
measurements is extended to multiple measurements, with provisions for the
primacy hierarchy and sensitivity. This composite validation metric is
essential for quantitatively evaluating comparisons with experiments. To mount
successful and credible validation in magnetic fusion, a new culture of
validation is envisaged.Comment: 27 pages, 1 table, 6 figure
Toward a first-principles integrated simulation of tokamak edge plasmas
Performance of the ITER is anticipated to be highly sensitive to the edge plasma condition. The edge pedestal in ITER needs to be predicted from an integrated simulation of the necessary first-principles, multi-scale physics codes. The mission of the SciDAC Fusion Simulation Project (FSP) Prototype Center for Plasma Edge Simulation (CPES) is to deliver such a code integration framework by (1) building new kinetic codes XGC0 and XGC1, which can simulate the edge pedestal buildup; (2) using and improving the existing MHD codes ELITE, M3D-OMP, M3D-MPP and NIMROD, for study of large-scale edge instabilities called Edge Localized Modes (ELMs); and (3) integrating the codes into a framework using cutting-edge computer science technology. Collaborative effort among physics, computer science, and applied mathematics within CPES has created the first working version of the End-to-end Framework for Fusion Integrated Simulation (EFFIS), which can be used to study the pedestal-ELM cycles
- …